[Linuxtrent] Re: Il led dell'hd lampeggia sempre e con un forte tichettio nell'audio
- From: Mario Alexandro Santini <alexmario74@xxxxxxxxx>
- To: linuxtrent@xxxxxxxxxxxxx
- Date: Fri, 14 Jan 2011 12:37:52 +0100
Ho scordato la parte principale, che aggiungo qui, dato che il messaggio lo
avete già letto:
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.11
Device Model: ST3500320AS
Serial Number: 9QM1DRQK
Firmware Version: SD15
User Capacity: 500,107,862,016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Thu Jan 13 18:23:30 2011 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has
ever
been run.
Total time to complete Offline
data collection: ( 634) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
Offline surface scan
supported.
Self-test supported.
Conveyance Self-test
supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before
entering
power-saving mode.
Supports SMART auto save
timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging
supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 117) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103b) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 118 099 006 Pre-fail
Always - 177889326
3 Spin_Up_Time 0x0003 094 094 000 Pre-fail
Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age
Always - 547
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000f 069 060 030 Pre-fail
Always - 9755821
9 Power_On_Hours 0x0032 100 100 000 Old_age
Always - 634
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail
Always - 1
12 Power_Cycle_Count 0x0032 100 100 020 Old_age
Always - 547
184 Unknown_Attribute 0x0032 100 100 099 Old_age
Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age
Always - 0
188 Unknown_Attribute 0x0032 100 098 000 Old_age
Always - 809
189 High_Fly_Writes 0x003a 099 099 000 Old_age
Always - 1
190 Airflow_Temperature_Cel 0x0022 074 065 045 Old_age
Always - 26 (Lifetime Min/Max 16/26)
194 Temperature_Celsius 0x0022 026 040 000 Old_age
Always - 26 (0 13 0 0)
195 Hardware_ECC_Recovered 0x001a 040 032 000 Old_age
Always - 177889326
197 Current_Pending_Sector 0x0012 100 100 000 Old_age
Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age
Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
--
Ciao,
Mario
Other related posts: