[access-uk] Re: TVonics Setup Questions
- From: "Steve Hyde-Dryden" <csdryden@xxxxxxxxxxxxxx>
- To: <access-uk@xxxxxxxxxxxxx>
- Date: Tue, 8 May 2012 20:25:35 +0100
Hi Carol, I'm afraid I'm not sure on that one. If it's missed the speech
start up at the tuning stage you might have to go through the manual speech
start up. I think these were posted on the list recently. The problem I
have is that we recently had an extension done and the telly is in a
different room now. The loft ariel is accessible at the other end of the
property smiles. I need to get it redirected. I tried a little set top
ariel which was totally crap! Haha, picked up about 60 stations but the
signal was very intermitten. So, I have to wait now to get the ariel sorted
before I can play! Haha
Steve
-----Original Message-----
From: access-uk@xxxxxxxxxxxxx [mailto:access-uk@xxxxxxxxxxxxx] On Behalf Of
Carol Pearson
Sent: 08 May 2012 15:53
To: access-uk@xxxxxxxxxxxxx
Subject: [access-uk] Re: TVonics Setup Questions
Thanks, Steve:
OK, so all I need in is the aerial cable from outside and the HDMI cable
plugged into the socket nearest the aerial cable. Right?
I'll give that a go later (hopefully this evening) when I have someone else
to help me reach the power point so I can start from scratch once again.
Should I still be able to press the blue button before tuning commences in
order to get speech on? (If nobody knows a definite answer on this one then
I'll just wait and hopefully get it tuned first.)
--
Carol P
---- Original Message ----
From: "Steve Hyde-Dryden" <csdryden@xxxxxxxxxxxxxx>
To: <access-uk@xxxxxxxxxxxxx>
Sent: Tuesday, May 08, 2012 3:39 PM
Subject: [access-uk] Re: TVonics Setup Questions
> Hi Carol, smiles. Me too! Pressing the blue button for me didn't get
> the speech on either however a couple of points. If you are
> connecting your box via the RF ariel leads then you don't need the
> HDMI connector. If you want to use the HDMI connector, then you don't
> need to run the ariel cable from the box to the tv. I'd advise using
> the HDMI as you'll gain the benefits of auto switching etc.
>
> Hope that helps
>
> Steve
>
>
> -----Original Message-----
> From: access-uk@xxxxxxxxxxxxx
> [mailto:access-uk@xxxxxxxxxxxxx] On Behalf Of Carol Pearson
> Sent: 08 May 2012 15:00
> To: Access UK Mailing List
> Subject: [access-uk] TVonics Setup Questions
>
> Hi all,
>
> Well, thankfully my TVonics arrived today and I've tried setting up as
> follows:
>
> My aerial cable (from outside) is in the Aerial in socket, The other
> aerial socket has the aerial between box and TV. The HDMI cable
> between TV and box as stated in instructions.
>
> It does not state in the instructions whether you need to tune the box
> independently first, before putting on the TV, so we've tried tuning
> both ways. On each occasion, we've said OK to tune, since there
> doesn't seem to be any other option my friend can see, and the tuning
> has just gone on and on ... so we've turned off the power to the box,
> given it a good 20 seconds and tried again with TV on, but still no
> go!
>
> In addition, when we first switched on, we pressed the blue button, as
> speech didn't automatically come on. We still haven't managed to get
> speech on as there seems to be no bypassing the channel search.
>
> Hopefully someone somewhere can pinpoint where we've gone wrong,
> advise of anything else I can do, and we can get up and running very
> soon.
>
> Thanks for any advice for this poor novice who's never set up a TV and
> box before! <Smiles>
>
> --
> Carol P
>
> ** To leave the list, click on the immediately-following
> link:-
> **
> [mailto:access-uk-request@xxxxxxxxxxxxx?subject=unsubscribe]
> ** If this link doesn't work then send a message to:
> ** access-uk-request@xxxxxxxxxxxxx
> ** and in the Subject line type
> ** unsubscribe
> ** For other list commands such as vacation mode, click on the
> ** immediately-following link:-
> ** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=faq]
> ** or send a message, to
> ** access-uk-request@xxxxxxxxxxxxx with the Subject:- faq
>
> ** To leave the list, click on the immediately-following
> link:-
> **
> [mailto:access-uk-request@xxxxxxxxxxxxx?subject=unsubscribe]
> ** If this link doesn't work then send a message to:
> ** access-uk-request@xxxxxxxxxxxxx
> ** and in the Subject line type
> ** unsubscribe
> ** For other list commands such as vacation mode, click on the
> ** immediately-following link:-
> ** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=faq]
> ** or send a message, to
> ** access-uk-request@xxxxxxxxxxxxx with the Subject:- faq
** To leave the list, click on the immediately-following link:-
** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=unsubscribe]
** If this link doesn't work then send a message to:
** access-uk-request@xxxxxxxxxxxxx
** and in the Subject line type
** unsubscribe
** For other list commands such as vacation mode, click on the
** immediately-following link:-
** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=faq]
** or send a message, to
** access-uk-request@xxxxxxxxxxxxx with the Subject:- faq
** To leave the list, click on the immediately-following link:-
** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=unsubscribe]
** If this link doesn't work then send a message to:
** access-uk-request@xxxxxxxxxxxxx
** and in the Subject line type
** unsubscribe
** For other list commands such as vacation mode, click on the
** immediately-following link:-
** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=faq]
** or send a message, to
** access-uk-request@xxxxxxxxxxxxx with the Subject:- faq
Other related posts: